好多水好爽小荡货h

 Service hotline National Service Hotline:

195-2099-7653

Wuhu container shelf price_ Wuhu loft shelf price

How to calculate the price of attic shelf

It depends on the size of your warehouse, the material specification and quantity of the selected shelf

Higris shelf

What is the price of loft type shelf

Attic type shelf is calculated according to the area, in addition, stairs also need to calculate money

Specific need to ask the manufacturer

Is the price of attic shelves expensive

In fact, loft shelves can make better use of space, so the price will certainly be higher. The most common size is about 100000. However, if the space utilization rate is doubled, the cost is still much lower than building a warehouse.

Shelf selection is mainly about quality, and how to say quality at present, I write a little long below, have time to have a look, it's good for you to buy shelves.

Storage shelf quality standards are also many, from the load-bearing, design, specifications, technology, materials and so on.

Load bearing: according to your requirements, the shelves are divided into light shelves, medium shelves and heavy shelves. Different specifications have different designs and specifications. This load-bearing refers to the weight that each layer of the standard four layer shelf can bear. Light shelves generally bear about kg, medium-sized shelves generally bear about kg, and heavy shelves generally bear more than 500 kg. The higher the load-bearing, the higher the quality requirements. Of course, the better the quality. But if you put some light things and buy a 500 kg shelf, it's a bit wasteful. If the pursuit of quality, the highest choice to medium-sized shelves on the line, after all, the light shelf market is too chaotic, too miscellaneous, especially on the Internet, dare to bid, but the quality is estimated to put up 30 kg will collapse. However, the brand shelves of large factories still have safety factor on their own standard load-bearing, some are 1.2, some are 1.3, and some large brands are 1.6 or higher, that is to say, the bearing capacity exceeds the nominal weight by 1.6 times, and there will be no safety risk in the short term. It may cause some deformation for a long time, but it is guaranteed that it will not collapse and cause accidents. At present, I know that only the hegris brand in the north can meet this standard, and there are three or four brands in the south.

Design: at present, the domestic market design standards are particularly disordered. Many manufacturers have turned the C-shaped steel butterfly hole rack of light-duty shelves into medium-sized shelves or even heavy-duty shelves, regardless of the safety factor. Of course, there are some large factories and brands that apply the design standards of traditional heavy and even super heavy (load-bearing from one ton) shelves to heavy-duty shelves and medium-sized shelves. The most typical example is the medium-sized shelves of higris, which uses U-shaped steel columns and eagle mouth cards, and increases the thickness of safety pins. In other words, with the same thickness and height of U-shaped steel and C-shaped steel, the steel consumption of U-shaped steel column is about 1.3-1.5 times of that of C-shaped steel column, and the structural safety is more than twice. In addition to the column, on the cross brace diagonal brace, the medium-sized shelf of higris adopts the same 10 thick and thin stainless steel screws fixed as the super heavy shelf, instead of the welding method used by most manufacturers. The firmness is three or four times more strong. Some manufacturers weld the cross diagonal brace at one time, and two small solder joints fool things, and can be broken down by hand.

Specifications: it mainly depends on the thickness of the materials used for various parts (pure steel before painting, many factories and households fool people with the thickness after painting), the light shelf with good quality is generally 0.4 from the light shelf, and 0.6 from the medium-sized shelf, which are the minimum standard. In fact, in theory, the light shelf should be 0.6, and the medium-sized shelf should be 0.8. Other parts of the material thickness should also be noted. Of course, the column is the most important part of the shelf load-bearing, and the thickness should be considered together with the design structure. The U-shaped steel structure is good. Generally, the thickness of 0.8 mm is higher than the actual bearing capacity of C-shaped steel 1.0 or even 1.2. Of course, the weight is heavier. Therefore, many shelf manufacturers use C-shaped steel columns, which are easy to process and appear thick, More than a third of the cost can be left. In addition, pay attention to the thickness after painting. The thickness of 0.8 mm thick plate after painting is about 1.2. Many manufacturers make a fool of the thickness after spraying. After spraying, it is 0.8 mm. In fact, 0.5 is good, and it is certainly not a good painting.

Technology: in fact, there is not much that can be said about this aspect. Large manufacturers have good technology and strict quality control. It can be said that there are two, one is degreasing and derusting, the other is one-time molding. For large manufacturers or manufacturers with strict quality, degreasing and derusting are operated by special tanks. There are several steps, such as a row of tanks, degreasing pools, rust removal pools, acid-base integrated tanks, phosphating pools, etc. each step is strictly immersed for 40 minutes to see the effect. If the effect is satisfactory, rinse it in the clean water tank, and enter the next step in 40 minutes, If the effect is not satisfactory, it will be 40 minutes. Rinse each step for 40 minutes. So it takes almost a day or more for a set to come down. Small factories, including some large factories now, adopt the method of spray production line. After a set is finished in half an hour, the effect is estimated to be only one third of the soaking. The appearance is OK, but many corners can not be handled inside the parts, so the service life can be imagined. I know, in the north, I see more than 100 factories, only Hebei Walker metal's higris brand is still operating in the way of soaking. There are only three factories in the south. In the past, dozens of factories in the South were soaked, but now they are all changed to spray. After all, the time is saved by 10% and the cost is reduced by 10%. One time molding is mainly a test of machinery. Large factories can buy high-grade machinery. Seven or eight bends with different angles on the shelf can be formed at one time to ensure the best state of materials. Small factories can only use ordinary machines to process one bend at a time and seven or eight bends to process seven or eight times, resulting in metal fatigue and seriously affecting quality.

What is the price of loft type shelf

Attic type shelf is calculated according to the area, in addition, stairs also need to calculate money

Specific need to ask the manufacturer

What is the price of the attic shelf

Attic type shelf is calculated according to the area, in addition, stairs also need to calculate money

Specific need to ask the manufacturer

Which loft shelf does better, still have attic type shelf price generally how much

Hebei Walker metal - higris loft shelf

2005张筱雨魅惑_百度云资源共享分享群组链接_宅男软件猫咪破解版

http://2.jwvision.cnhttp://0.jwvision.cnhttp://1.jwvision.cnhttp://7.jwvision.cnhttp://3.jwvision.cnhttp://2.jwvision.cnhttp://6.jwvision.cnhttp://0.jwvision.cnhttp://3.jwvision.cnhttp://3.jwvision.cn